They are making a number of great points related to Tools You Need to Install a New Bathtub overall in the content on the next paragraphs.
Mounting a bathtub isn't exactly rocket science, however it does require solid plumbing, woodworking, and also sometimes, tiling abilities. Changing an old tub with a new one is also a reasonably hard task. If the old tub is conveniently obtainable, the task can relocate rapidly; if you need to open a wall to eliminate the old tub and also place the new bathtub, the job is a lot harder. In either instance, the task is within a home handyman's abilities, although you will certainly require an assistant to move out the old bathtub as well as embeded in the new one. See to it you have certified on your own for the job as well as fit attempting it. Instead of employing a professional to take control of a halfway-completed project, it is better to consider using one prior to you begin. Chances are you may need a professional plumber to make tube connections.
This post will aid you install a brand-new tub in your bathroom if you have actually already bought a brand-new tub as well as don't require to transform the plan of your previous water supply pipes.
Your devices as well as product checklist must comprise the following:
- New Bathtub
- Hammer
- Pipeline Wrenches
- Prybar
- Safety Glasses
- Level
- Pliers
- Adjustable Wrench
- Putty Blade
- Screwdriver
- Cold Knife
- Measuring tape
- Pipe Caps
Getting ready for the Installation
Firstly, the supporting framework supplied with the bath should be fitted (if needed) according to the manufacturer's directions. Next off, fit the faucets or mixer to the bathtub. When suitable the tap block, it is important to make sure that if the faucet comes with a plastic washing machine, it is fitted in between the bath and also the faucets. On a plastic bath, it is additionally practical to fit a supporting plate under the taps system to prevent strain on the tub.
Fit the adaptable tap adapters to the bottom of the two taps making use of 2 nuts and also olives (often supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and after that pass the electrical outlet with the hole in the bath. Use the nut provided by the maker to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the flexible overflow pipeline to the overflow outlet. Afterwards, screw the pipe to the overflow face which must be fitted inside the bathroom. Make certain you use all of the supplied washers.
Link the catch to the bottom of the waste outlet on the bath tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the catch to the electrical outlet. Attach all-time low of the overflow tube in a comparable manner.The bath must currently be ready to be fitted in its final setting.
Removing Old Touches
If you need to change old taps with new ones as a part of your installation, then the first thing you ought to do is disconnect the water supply. After doing so, switch on the taps to drain any type of water remaining in the system. The process of removing the existing taps can be fairly troublesome due to the limited accessibility that is frequently the situation.
Make use of a container wrench (crowsfoot spanner) or a tap device to undo the nut that connects the supply pipes to the faucets. Have a towel prepared for the remaining water that will certainly originate from the pipelines. When the supply pipelines have actually been removed, make use of the very same tool to loosen up the nut that holds the taps onto the bath/basin. You will certainly require to quit the solitary taps from transforming throughout this procedure. Once the faucets have actually been eliminated, the holes in the bath/basin will certainly have to be cleansed of any old securing compound.
Prior to proceeding to fit the new faucets, compare the pipeline links on the old faucets to the brand-new taps. If the old taps are longer than the new faucets, then a shank adapter is required for the new taps to fit.
Installing the Tub
Utilizing both wooden boards under its feet, position the bath tub in the needed position. The wooden boards are valuable in evenly spreading out the weight of the bath tub over the area of the boards as opposed to concentrating all the weight onto 4 tiny points.
The next objective is to make sure that the bath tub is leveled all round. This can be accomplished by examining the spirit level and readjusting the feet on the tub till the spirit level reads degree.
To set up faucets, fit all-time low of the outermost versatile faucet connector to the appropriate supply pipeline by making a compression join; after that do the very same for the other tap.
Activate the water supply and also examine all joints and also new pipework for leaks as well as tighten them if needed. Fill the tub and additionally check the overflow outlet as well as the normal electrical outlet for leaks.
Ultimately, take care of the bathroom paneling as defined in the manufacturer's instruction manual. Tiling as well as sealing around the bath tub ought to wait till the bathtub has been made use of at least once as this will resolve it into its last placement.
Fitting New Taps
If the tails of the new taps are plastic, then you will certainly require a plastic port to prevent damage to the thread. One end of the adapter fits on the plastic tail of the faucet and also the other end gives a connection to the existing supply pipes.
If you require to fit a monobloc, then you will certainly need lowering couplers, which connects the 10mm pipeline of the monobloc to the basic 15mm supply pipe.
Next, place the faucet in the placing hole in the bath/basin guaranteeing that the washers remain in place between the tap and the sink. Protect the tap in position with the supplier offered backnut. Once the tap is firmly in position, the supply pipelines can be attached to the tails of the taps. The faucets can either be linked by utilizing corrugated copper piping or with regular faucet connectors. The former type must be connected to the faucet ends first, tightening only by hand. The supply pipelines can later be attached to the various other end. Tighten both ends with a spanner after both ends have actually been linked.
Tiling Around the Tub
In the area where the bathroom satisfies the floor tile, it is necessary to secure the accompanies a silicone rubber caulking. This is important as the installation can relocate enough to crack a stiff seal, triggering the water to permeate the wall surface in between the bath and also the tiling, causing difficulties with wetness and also possible leakages to the ceiling below.
You can choose from a selection of coloured sealants to assimilate your fixtures and also fittings. They are offered in tubes and cartridges, and can securing spaces up to a size of 3mm (1/8 inch). If you have a bigger space to fill up, you can load it with spins of drenched paper or soft rope. Remember to always fill the bathtub with water before securing, to allow for the movement experienced when the tub remains in usage. The sealer can crack relatively early if you do not consider this activity prior to sealing.
Additionally, ceramic coving or quadrant tiles can be made use of to border the bath or shower tray. Plastic strips of coving, which are easy to use and also cut to dimension, are also easily available on the marketplace. It is advisable to fit the floor tiles utilizing waterproof or water resistant adhesive and also cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I came across that page about How to Install a Bathtub while doing a lookup on the internet. For those who enjoyed our post if you please don't forget to pass it around. Many thanks for your time spent reading it.
We're here 24/7.
Comments on “Your Plumbing Crash Course: What You Must Have for Installing a Bathtub”